Spare parts for Futurol

Tandem roller for sectional garage door (unit) Roller axle diameter 11mm Rod length: 95mm Rollers diameter 45mm Ball bearing Sold without hinge support (available here)

Nylon Overmolded Bearing Pulley - Single Groove (per unit) For 10mm Ø shaft Pulley Ø 50mm Ball bearing Per unit Optional: 1x M10x40 screw + 1x M10 lock nut + 2x M10 thin nuts Highly durable ball bearing with ABS overmolding. The Nylon pulley is more durable than a steel pulley, by choosing it you extend the lifespan of your sectional door.

Hinge lateral support roller for sectional garage door (unit) White lacquered side hinge to be used at the joints between the panels of a sectional garage door, designed to support rollers with an 11mm diameter axle. To be used with tandem rollers or side sectional door rollers.

Bottom roller supports for sectional garage doors delivered in pairs with 2 white rollers. Roller axle diameter 11mm Roller diameter 45mm Ball bearing Axle L95mm or L150mm depending on version For wide doors (>3500mm), prefer the double model for better support and roller maintenance. This extends the lifespan of your door.

Fixed Upper Sectional Garage Door Roller Support (the pair) Roller axle diameter 11mm Roller diameter 45mm Ball bearing Designed for double rail doors This pair of fixed upper sectional garage door roller supports is compatible only with double rail sectional garage doors.

Suspension bracket and rail support, made of galvanized steel, to facilitate the installation of garage doors. Two available lengths: 450, 600 or 750 mm Two types of supports (+ 1 M8 bolt): for single rail or double rails Suitable for installing sectional or up-and-over garage doors.

Telescopic Spacing Crossbar 2x1.80 meter (per unit) This crossbar allows you to attach the back of your garage door rails to the ceiling and/or walls. It can extend up to a maximum of 3m. A model of 2x2.40m, which can extend up to 4.2 meters, is available here. As this item is bulky, the delivery time may be slightly extended. Thank you for your understanding.

Telescope Spacing Beam 2x2.40 meters (unit) This spacing beam allows you to secure the back of your garage door rails. It can extend up to a maximum of 4.2 meters. A model of 2x1.80m, which can extend up to 3 meters, is available here, with delivery by Colissimo.

Very useful for unlocking your engine from the outside in case of a power outage! Comes with 2 keys Originally designed for insulated panels 20 to 40mm If insulated 40mm or 20mm => use the standard kit without support If insulated 60mm or single metal (non-insulated) => use the ISO60 support (provided with 8 rivets)

Additional side lock for garage door (per unit) Rod diameter: 12mm Supplied with 4 sheet metal screws 6.3x15 This side lock will add an extra locking point to your garage door. Drill the guide rail so that the side lock rod engages and thus blocks the opening. For more security, install one on each side of the door. Installation instructions: example of installation on a sectional door

Suitcase Handle allowing you to manually operate your sectional or sliding garage door. PVC material Supplied with 4 screws 5.5x25mm (handle only) or 4 screws 5x40mm (for the complete set int+ext) Black or white color Attaches to the inside of the door, ideally at least 2 screws should be in a panel reinforcement.

Handle for sectional garage door, surface-mounted, delivered in pairs. For temporary manual use of your sectional garage door, you can add this small handle. Very discreet, they will allow you to have an additional grip on the panel to lift your door more easily. Sold in pairs White ABS Screws not provided (to be defined according to your panel type)

ONE X motorization for sectional and up-and-over garage doors up to 12m², with integrated LED lighting, obstacle detection, and optional smartphone connectivity. Automation delivered complete with: 1 ONE motor head with 140cm power cable 2 ONE transmitters 1 chain rail 1 ceiling mounting kit 1 connecting arm for sectional door and 1 connecting arm for up-and-over door

Bi-material frame seal for sectional garage door (the unit) This joint is clipped onto the edges of the uprights or the top rail and is easily overlapped with a pruning shear or cutter. Attention, this seal is compatible with Spadone doors and also Novoferm Maeva (1, 2 and 2b) sectionnal door. We do not guarantee complete compatibility with other brands.

Spring cover gasket for sectional garage door jamb (the unit) Length: 2000 mm This joint must only use the right-hand side of the rail (see diagram). It can be easily overlapped with a hacksaw or pruning shears.

Bimaterial flap seal for sectional garage door bottom (the unit) This gasket can be fixed at the bottom of the door panel for floor sealing. Available in 2 sizes: 2420mm or 3020mm. For reasons of space and delivery, the seal is cut/folded in 2 parts.

This steel profile is inserted in the female part (bottom part) of the bottom panel of your sectional and serves as a support for the EPDM gasket (sold separately). Length 1295mm In galvanized steel Fixing screws supplied Choose the number of elements needed to cover the width of your door and cut to your convenience (hacksaw / saw)

EPDM rubber seal for garage door bottom. This very flexible gasket provides a better seal than the simple bib gasket. It can be cut with a cutter to fit custom-made garage doors.   CAUTIONThis rubber gasket fits into an  Aluminum seal support profile sold separately

Steel pulley diameter 70mm Single Throat Ball Bearing (the unit)   This pulley was used on our old horizontal spring sectional garage doors. An optional spring holder is available for this purpose.

Centering Rings (Set of 6) Width : 10 mm Inside diameter : 11.5 mm Material: Steel These bushings are inserted on the axes of the rollers and allow the garage door to be centred. They thus limit the movement of the door leaf.  If your garage door nevertheless shifts too much to one side, you may want to reconsider the parallelism of the tracks.

Hexagon head sheet metal screw 6,3x25 mm Length under head: 25 mm Easily installed with a screwdriver and a size 10 hexagonal bit.

Central hinge for sectional garage door and side garage door (the unit) This hinge joins two panels of a door. It is suitable for residential and industrial doors. Material: steel, white lacquered

These reinforced anchor brackets (or mounting brackets) allow your up-and-over garage door or sectional garage door to be mounted on the wall. Dimension: 45 x 77 x H60 mm Material: galvanized steel Per set of 7 brackets (M8 screws and nuts supplied) Simply bolt these brackets to the studs (usually 3 brackets per side) and attach one to the top rail, then anchor them to the wall.

Roller for up-and-over and sectional garage doors Roller diameter : 45mm Spindle diameter: 10 or 11mm Ball bearing 3 models: Spindles Ø 10mm - Spindles lenght (without roller) 85mm Spindles Ø 11mm - Spindles lenght (without roller) 95mm Spindles Ø 11mm - Spindles lenght (without roller) 150mm   The standard diameter of the roller spindles is 11 mm.For special requests, you can also opt for the 10 mm diameter version.

One-piece PVC gasket This extruded gasket consists of a rigid PVC U-profile and a very flexible PVC bottom section with an outer flange and a wide inner lip. To be fitted on the bottom of the panel and riveted (black rivets supplied) Attention, this joint is cut in 2 parts in order to be accepted by Colissimo. => Click here for the 1 part version only

2-point lock set for sectional garage door (the unit) Allows you to add 2 locking points on your sectional door. Caution: recommended for manual door only. Kit Contents : 1 Lock box 2 points 1 Cylinder 10x70 (for 40mm insulation) 1 Handle Int/Ext + 1 PVC Plate 2 Autolatch + 2 strikers 1 Cable (to be crossed over) 8 sheet metal screws + 4 bolts M8

Nylon double groove ball bearing pulley For shaft Ø10 mm Ø of the pulley 50mm Ball bearing with ABS sumoulage Optional: 1x screw M10x40 + 1x lock nut M10 + 2x thin nuts M10 This double grooved pulley is used on doors with double cables. The nylon pulley is more resistant than a steel pulley, by choosing it you extend the life of your door.

These top brackets are adjustable in height and allow a finer adjustment of the top panel veneer on the joint of the top rail. Made of thick steel Pair, sold with 2 casters Stem of roller Diam 11 - L95mm Diameter of the roller 45mm Ball bearing For double track door (sheet metal screws not supplied)

On older sectional doors, the cable is outside the rail and therefore cannot be hooked directly onto the base support, we have created this kit. Content of the set: 1 pair of bottom bracket roller D&G 1 pair of remote cable hanger G&G + axis 2 cable extensions (to offset the cable if necessary) 2 ball-bearing castors (Rod Ø11 L95) 4 M8x20 10 sheet metal screws 6.3x25

Steel support with adjustable guide.roller The movable guide roller offers an additional adjustment for a sectional garage door compared to a simple roller. Indeed, their adjustable spacing allows you to adjust your panel on the peripheral joints. Supplied with one roller ball bearing: Axis of the roller Ø11mm - L95mm Wheel diameter 45mm

Roller with Nylon overmolded bearing (the unit) For 10 mm shaft Outer roller diameter 50mm Flat-bottomed inner groove (approx. 6x5mm) Ball bearingHeavy-duty ball bearing with sumoulage. The bottom being flat, it allows the movement of your panels on a rail.The nylon roller body is highly wear resistant.

This aluminium profile fits into the bottom of the panel and supports the EPDM gasket (sold separately). Also suitable for edged panels For 40mm thick panels to be cross-referenced at your convenience delivered with steel rivet two sizes available : 1250mm and 1500mm Raw aluminium

This very flexible threshold seal provides a double seal when closing at the bottom of your garage door, in addition to the seal fitted under your lower panel. Weatherproof, rainproof, stops water, drafts, leaves/dust to keep your garage clean and dry Designed to allow the silent passage of a vehicle driving over it In PRODENE 503 70 SH BLACK We recommend PU40+ glue (sold separately)

Additional lock for up-and-over or sectional garage door (the unit) Supplied with 8 sheet metal screws 6.3x16 Provided with a trigger to be fixed This lock will add an extra locking point to your garage door.

This pulley is designed to be mounted on an axle with a diameter of Ø10 mm - External pulley diameter 100 mm- Max. cable diameter: 5 mm- Max. door weight: 450 kg- Ball bearing  Sold individually Optional: 1x M10x40 screw + 1x M10 lock nut + 2x M10 thin nuts

Bimaterial side seal for industrial sectional garage door (the unit) This seal can be attached to the edge of the garage door jambs by interlocking. Length: 1250mm

This one-piece extruded PVC bead gasket consists of a rigid PVC U-profile and a very flexible PVC bottom part with an outer bead and a wide inner lip. To be fitted on the bottom of the panel and riveted (black rivets supplied) Delivered in one piece by special carrier => Click here for the 2-part version with Colissimo delivery

This support with movable guide roller offers an additional adjustment for an industrial sectional garage door compared to a simple roller. Indeed, their adjustable spacing allows you to adjust your panel on the peripheral joints. Steel support with adjustable guideroller Designed for 11mm roller diameter shaft (not included)

These parts allow the rear attachment of the rails to the spacer bar. Their design allows them to slide easily to adjust their position on the spreader bar. Dimension: 54x120mm In galvanized steel Sold in packs of 2 (1 left + 1 right) 6 screws + 6 M8 nuts supplied

Double roller to ensure movement on the top rail of sectional garage doors with lateral movement (the unit) Wheel diameter: 45mm Ball bearing + 1 BTR screw 150mm M8 threaded + 1 brake nut M8 Sold without support hinge (available here)

Roller for floor guidance of laterally moving sectional garage doors (the unit) Roller diameter 20mm Ball bearing Sold with a pin Sold without support hinge

Centering rings (set of 10)  Width: 4 mm  Inner diameter: 11 mm  Material: Black PVC These spacers with an open shape allow their insertion (or removal) directly on the caster rod! Unlike classic rings where you have to disassemble the support and the caster to insert the ring on the rod then reassemble everything.

These basic anchor brackets (or mounting brackets) allow your garage door to be mounted on the wall. Dimension: 95 x 38 x H38 mm Material: galvanized steel thickness 2mm Per set of 5 brackets (screws not supplied) Simply bolt these brackets to the studs and attach one to the top rail and then anchor them to the wall.

Reduced size EPDM flange seal for garage door bottoms or any other case! - Flexible and hollow profile, allows a better seal than the simple bib seal- Easy to install- Discreet, it is only 15mm visible- To be cut at your convenience using a cutter- Delivered rolled WARNINGThis seal fits into a profile sold separately:- Aluminum seal support profile

White lacquered side hinge to be used at the joints between the panels of a sectional garage door, designed to support castors with an 11mm diameter axle. Model with PVC tube to limit noise and friction. For use with tandem wheels and guide roller for a side sliding sectional door.

This receiver makes your garage door motor compatible with connected systems. You can open your door, close it and check its status from your smartphone with voice command, on the Meross (Android / iOS) or Apple Home app. Easy to install, it is connected to the motor on the terminals for the push button, a wired sensor detects the position of the door and it is supplied by a power outlet.

Very useful for unlocking your engine from the outside in case of a power outage. Delivered with 2 keys Designed for insulated doors up to 50mm thick. Model LiftMaster 1702EV

This blocker ensures the immobilization of a garage door gate in the open position against a wall or other Made of injected PVC, available in white or black Screws not provided, adapt according to the support Very easy to install: - Attach part A to the gate (preferably in a reinforcement) - Fix part B on the facing wall (or other) - Part A fits into part B for temporary holding of the gate in the open position

Futurol no longer distributes this reference, so this is our only solution for replacing their remote control model. Pack: 1 ONE receiver + 2 ONE V5 remotes 1 receiver - 433mhz - To be connected to your Futurcom motor (version with black cover & central black button) - Makes your motor compatible with our ONE transmitter / ONE code panel 2 ONE V5 remotes Easy to implement     - 2 wires => 12 /24V     - 2 wires => dry contact