Spring for overhead garage door - Type A
Outer diameter: 19 mm
Length without tension: 355 mm (including loops)
Working length: 700 to 800 mm
Price:€14.40
Springs for up-and-over garage door
All our overhead garage doors are equipped with a unique model of tension spring: the spring A. Only their number varies depending on the size and insulation of your door.
Doors from before 2000 equipped with a single spring on each side (diameter 5 to 6 centimeters) have become non-compliant for safety reasons. With our multi-springs, if one breaks, your garage door will not fall. Our hooks, loops, brackets, and straps allow these spring kits to be easily adapted to most overhead doors on the market.
When one of your old springs breaks, it is advisable to change the springs on both sides of your overhead garage door to maintain an identical pulling force on the left and right. Otherwise, your door could become unbalanced.
If needed, our team is here to advise you on the repair to be carried out on your garage door, do not hesitate to contact us.
These brackets allow you to attach your type A springs to the bottom of the post and the arm of your tilting door.
You can place up to 7 Type A springs per side with these brackets.
The old single "large springs" placed on each side of the old tilting garage doors are now non-compliant. We use a single spring model by varying their number. These springs are assembled using this pair of brackets.
Price:€12.00
Multi-spring kit for overhead garage door + 2 hooks (the set)
Replaces old "large springs" diameter 4 to 5cm
Length of the kit (hooks + springs): 460 mm
Consult the table to know the number of springs for your door (Indicative values, balancing may vary depending on the design)
Warning: (1 kit = 1 side)
Advice: change both sides at the same time to keep your door balanced, that is 2 kits.
Price:€64.90
Steel swing arm for overhead garage door.
Reversible arm model suitable for right or left. Arm sold separately without accessories.
3 arm lengths available:
Door height 1800-1999 Ref. M - 1000mm
Door height 2000-2249 Ref. S - 1100mm
Door height 2250-2499 Ref. X - 1215mm
If the length of your installed arms differs from those indicated, change both sides to keep your door balanced.
Price:€66.00
Tilt stop kit, designed to equip the left and right sides of a swinging garage door:- 2 apron tilting stops (to be fixed on the frame)- 2 tilting stops frame (to be fixed on the uprights)- 4 adjusting shims (to improve the garage door's plating)- 8 sheet metal screws 6.3x25mm
Price:€23.40
Steel tensioning strap for manual up-and-over garage door springs.
Allows you to connect the springs attached to the bottom of your door jamb to the door arm axle.
Sold in pairs
In galvanized steel
Width of the strap: 20mm
2 sizes: 6 or 13 holes
(Sold alone, without spring hook)
Price:€12.90
Bridge strap for a motorized or manual up-and-over garage door arm.
The pair
For overhead door
4 screws M8x20 + nuts supplied
Sold alone, without spring hooks
(sold alone, without spring hook)
Price:€24.96
3 springs type A (Øext 19mm / L total 355mm)
1 triangle acc. springs high with T-connector for hanging Superior strap side
1 triangle acc. low springs with a hole for hanging lower (Useful if you don't have a hook at the bottom of your post. Drill and bolt at the foot of the jamb if necessary).
1 bolt M8
Provision for a non-insulated tilting device
Attention: 1 kit = 1 side
Price:€44.90
Very useful to facilitate the attachment of a spring
Oval shape
Dim int : (h)45 x (b)14
Opening: (m) 7.5mm
Section: (d) 6mm
C.M.U : 200 kg
Made of galvanized steel
Price:€3.60
Only for EURONORM CT up-and-over garage doors size 2400x2000H.To replace the 2 big springs which are no longer up to standard:4 springs Type C Ø22mm L715mm2 EURONORM mobile pulleys (with 2-hole supports)2 cables Ø3mm with L3m loop + 2 leads2 EURONORM perforated fasteners2 triangles acc spring EURONORM4 PVC rings
Price:€109.50
Bridge strap for a motorized overhead garage door arm
Allows you to connect your springs to the door arm axis. This jumper strap (thick sheet metal perforated with 7 holes + bolted upper part), recommended for insulated doors and preferably large size (H>2125).
2 screws M8x40 + nuts supplied
Sold alone, without spring hooks
Price:€36.96
The up-and-over door shoes come in the lower part of the uprights, they perform 3 functions:
hang the springs at the base of the upright
peg the upright to the floor
in the case of a door equipped with 2 locks in the corners, use the striker plates to keep the door locked.
Sold without accessories:- 1 leftshoe - 1 right shoe
Price:€16.20
Cables for EURONORM CT up-and-over doors up to 2.4m height
2 Steel cables Ø3mm , L3m with loops
2 Acc. Perforated cable Tilting EURONORM
4 anti-friction PVC washers
Supplied with 2 additional seals (if cable cut for intermediate sizes)
This cable system replaces the old system and allows you to adjust the tension of the springs.
Price:€25.00
Actuator for an up-and-over garage door
Brand Airax réf 512439 C350 240702A0 1100N
Force 1100N
370mm Ø10mm rod, M8 threaded at the end
Body Cylinder Ø22mm of 495mm, eye Ø8 at the end
Total length 890mm
Sold per unit
Price:€84.00
SL locking clip for locking the arm bracket placed on the frame of a Spadone, Novoferm, Hörmann and Tubauto up-and-over garage door.
This axle brake is designed to fit onto a Ø10 axle with an 8mm diameter groove.
Steel
Sold in sets of 2
Also compatible with Hörmann sectional low brackets Part No. 3014657 and tilting brackets N80 / F80 / Ecostar Part No. 1071001
Price:€7.50
This type of part is used on some up-and-over doors with single large springs on each side (usually German doors or older Doitrand models).
in steel thickness 3 mm
sold alone or with their triangular supports (+4 M8 screws + lock nuts)
the pair
Price:€12.90
These parts are attached to the bottom left and right corners of your overhead door frame and allow connection to the end of the swing arm.
Made of steel
+ 4 sewing screws
+ 2 clips
The pair
Price:€14.40
This steel circlip is used by the EURONORM up-and-over door brand. It can be used for other purposes.
on the high and mobile pulleys
at arm level
designed to fit on a Ø12 axle with a groove
Sold in pairs
Caution: Only compatible with 12mm pins with a groove to engage the clip.
Price:€7.50
Oscillating arm for up-and-over garage door.
Reinforced model, powder-coated in Anthracite Grey RAL 7016
Sold as a single unit without accessories
3 arm lengths available:
Door height 1800-1999 Ref. M - 970mm
Door height 2000-2249 Ref. S - 1070mm
Door height 2250-2499 Ref. X - 1185mm
If the length of your installed arms differs from the one indicated, change both sides to keep your door balanced.
Price:€108.00
The installation of a single single spring on each side of a tilting garage door was widespread until the beginning of the 2000s, but now the standard currently in effect forbids us to propose it, in favor of multi-springs. Our current system is retrocompatible, to allow you to change your springs and repair your door, without the need to change it! We have thus designed a single spring model (type a), whose installed number will vary the power. Thus, for small tilting garage door of 240cm wide by 200cm high, in single sheet, 3 springs "Type A" by side of the door will suffice. On the other hand on a 3m gate of width, isolated 60mm and with an integrated gate, we can go up to 7 springs per side. All these small springs will replace your old big springs.
Profit? In case of breakage of a spring, your door will not fall sharply, because still supported by all other springs. In addition, the replacement of a single small spring A is then possible, at lower fresh. Our springs are designed and manufactured in a particular steel alloy, ensuring flexibility and rigidity, with an average life of 20,000 cycles, which to provide them with 15 years of operation at the rate of 4 daily openings of your door.
To keep these springs hold on your door, we imagined different supports, all of which are attached to the bottom of the tilting door and up on the strap that is connected to the bottom oscillating. This strap serves to adjust the power of the springs and allow their ideal positioning whatever the height of your door. Our tilting garage door springs can via all these tricks ride on the doors of our manufacture, but also on doors of other large European manufacturers, such as Hormann, Novoferm or Tubauto.
Tip for changing your springs: Block your garage door in the open position using a seal on each side, to change your springs safely. In this position, your springs will not be in tension, you can remove them more easily and without risk of injury.